Wilton 3400 Provozní pokyny

Procházejte online nebo si stáhněte Provozní pokyny pro Kotoučové pily Wilton 3400. Wilton 3400 Operating instructions Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - 7 x 12 Cut-off Band Saw

Operating Instructions — Parts Manual7 x 12 Cut-off Band SawModels: 3400/3410WHM TOOL GROUP2420 Vantage DriveElgin, Illinois 60124 Part No. 9078201Ph.

Strany 2 - Warranty and Service

10Controlling the cut:Hydraulic feed controlThe weight of the saw arm typically provides all ofthe force needed to move the saw blade through theworkp

Strany 3 - Table of Contents

11Changing blade speedsThe Models 3410 and 3400 are 4-speed cut-offsaws. The different speeds are obtained by changing theposition of the drive V-bel

Strany 4 - Specifications

12Right angle cuts --single pieces of stock1. Raise the saw arm to its full up, open position.2. Pull up on the quick release handle on the locking

Strany 5

13Figure 8: Placing workpieces in the vise

Strany 6

14MaintenanceReplacing blades1. Disconnect the saw from its electrical power source toprevent accidental start-ups.2. Raise the saw arm to its full

Strany 7 - Operating Instructions

15Blade alignment adjustmentsThe blade can suffer from several out-of-adjustmentconditions. These conditions are shown in Figure 10.Figure 11: Nomenc

Strany 8

16Replacing blade guideand support componentsAll component parts are secured with nuts, bolts,washers, or snap rings. To remove and replace anycompon

Strany 9 - Setting the blade guides

17Adjusting blade vertical:The blade guide bearing seat can rotate as needed tomake the blade vertical to the saw table. Follow theseinstructions.1.

Strany 10 - Using the stock stop

18Adjusting guide bearingsThere are eight side blade guide/support bearings.These bearings are installed in the bearing seat, and theseat is attached

Strany 11 - Starting a cut

19Replacing the drive wheel1. Complete steps 1 through 6 in Replacing blades.2. Remove the snap ring which secures the lower wheelto the gearbox out

Strany 12 - Angle cutting

Warranty and ServiceWMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service

Strany 13

20Servicing the hydrauliccontrol cylinderOver a long period of service the hydraulic controlcylinder may need replacement of its internal seals. Uset

Strany 14 - Maintenance

21Machine Set-upThe saw delivered to you has been adjusted at thefactory. A number of test pieces have been cut using thesaw to verify the accuracy o

Strany 15 - When to adjust the

22Installing the coolant kit1. Install the baffle in the tank so the pump is held at oneend of the tank.2. Put the tank and pump assembly in the fla

Strany 16 - Replacing blade guide

23Troubleshooting1. Use more pressure to tighten vise.2. Check stationary jaw pivot and lock bolts for tightness.3. Check quick release handle nut

Strany 17 - Test cutting to verify

241. Observe chip formation to be sure cutting is efficient.1. Adjust guide bearings according to instruction in thismanual.1. Increase blade tensi

Strany 18 - Adjusting blade

25Replacement PartsThis section provides exploded view illustrations that show the replacement parts for the Model 3400 and 34107-Inch x 12-Inch Horiz

Strany 19 - Installing the

26Exploded View - Saw Head

Strany 20 - Servicing the hydraulic

2750 5710551 Bearing pin 251 5710561 Eccentric shaft assy. 251-1 5517504 Center shaft assy. 252 5710571 Brush 153 5710581 Hex nut 3/8x24 454A 5710591

Strany 21 - Machine Set-up

28Exploded View - Saw Base

Strany 22

29109 9056991 Nut 3/8x7x14 2110 5711221 90 degree support 1111 5517529 HH screw 3/8x1-3/4 2115 5711271 Support shaft -5/8 15711771 Support shaft - 7/8

Strany 23 - Troubleshooting

3Table of ContentsCover Page ...

Strany 24

30Parts List - Hydraulic CylinderRef.no.Part no.DescriptionQty.1 5517547 Dust cover 12 5517548 Retaining ring 23 5517549 Oil-seal 14 5517550 Oil-pisto

Strany 25 - Replacement Parts

4Cutting capacityBlade speedsBlade driveMotorBlade guidesBlade sizeBlade wheelsDimensions (LWH)WeightWet cutting packageGeneralSpecificationsThe Wilto

Strany 26 - Exploded View - Saw Head

51. Always wear protective eye wear when operatingmachinery. Eye wear shall be impact resistant, protectivesafety glasses with side shields which co

Strany 27 - Parts List - Saw Head

6close as possible to the work piece.9. Always wear protective eye wear whenoperating, servicing or adjusting machinery. Eyewearshall be impact resis

Strany 28 - Exploded View - Saw Base

7Operating InstructionsUsing the viseThe vise on the saw table has two jaws. The jawclosest to the right hand side of the table is the stationaryjaw.

Strany 29 - Parts List - Saw Base

8eventually catch the thrust shaft and allow you to open orclose the locking jaw at its new lead screw position.When you slide the jaw to a new positi

Strany 30 - Description

9Adjusting stationary jaw forhigh accuracy angle cutting:1. Raise the saw arm to full height and lock it in positionwith the shut-off valve.2. Open

Komentáře k této Příručce

Žádné komentáře